fits  36-06 Big Twin (Excl. 2006 Dyna) (NU)

Used to install & remove the left hand threaded 1-7/8″ hex nut (35211-36 for 36-92 models & 35211-91B for 93-06 models) on the transmission mainshaft that holds the transmission pulley. Heat treated to have an extremely hard surface and a very tough core. Broached drive hole for maximum strength. Tight tolerance on hex for maximum surface area contact and no damage to nut while tightening. With inner pilot for good alignment. 1/2″drive. Cerakote finish. USA made.

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Transmission > Fast Eddy, transmission pulley / sprocket nut socket, 1-7/8″

fits  36-86 4-speed Big Twin with kickstart (NU)

Used to pull the starter clutch gear (33381-39 / 2446-39) with ease from the mainshaft, on models with kickstart. Will not slip off gear and will prevent damage to clutch gear or mainshaft. – Designed to stay together when you put it back in your toolbox, no hunting for individual tool parts – Manufactured from heat treated 4140 steel to last – Compatible with stock and most aftermarket 4-speed kickstart – 100% made in USA

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Transmission > Fast Eddy, 4-speed kicker gear / clutch gear puller tool

fits  06-17 (NU) Dyna; 07-24 Softail; 07-24 Touring

Used to install & remove the 2-1/4″ hex nut (35241-06, regular right hand threaded) on the transmission mainshaft that holds the transmission pulley. Heat treated to have an extremely hard surface and a very tough core. Broached drive hole for maximum strength. Tight tolerance on hex for maximum surface area contact and no damage to nut while tightening. With inner pilot for good alignment. 1/2″drive. Cerakote finish. USA made.

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Transmission > Fast Eddy, transmission pulley / sprocket nut socket, 2-1/4″

fits  07-23 Softail; 07-23 Touring; 06-17 (NU) Dyna

Used to install main drive gear inner & outer bearing on 6-speeds. Also installs main drive gear seal. Transmission must be removed from bike

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Transmission > MCS, 6-speed main drive gear bearing tool

fits  17-24 Touring, 17-24 Trike

Used to both pull the shifter shaft bushing (OEM 11000139 / MCS 572360) from the inner primary case. With the included installation driver the new bushing is installed. The use of this tool will allow the ‘thin wall’ design of this bushing to be easily removed and installed preventing possible damage to bushing or inner primary housing.

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Transmission > JIMS, shifter shaft bushing installer/remover tool

fits 

Used to pull the trap door on custom right side drive transmissions.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Transmission > MCS, right side drive trap door puller

fits  07-24 Softail; 06-17 (NU) Dyna; 07-24 FLT/Touring

– Remover is used to remove the transmission main drive gear from the main drive bearing on all 6-speed B.T. models – Installer is used to install the main transmission case bearing OEM 8967, 8967A (MCS 921472). Tool will provide a correct bearing angle for a straight insertion to prevent damage to the bearing bore during installation – Tool can be used without removing the transmission from the bike.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Transmission > MCS, main drive gear and bearing remover & installer tool

fits  80-06 5-speed Big Twin (Excl. 2006 Dyna)

Used to install MCS 526160 / OEM 12045 oil seal behind the shifter arm on 5-speed transmissions.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Transmission > MCS, 5-sp transmission case shifter shaft seal installer

fits  06-13 Dyna; 07-13 Softail, Touring; 84-05 XL Sportster (NU)

Used to install H-D 37101-84B shifter shaft seal behind the shifter arm on the transmission of 6-speed Cruise Drive’ H-D transmissions and some XL Sportster models.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Transmission > MCS, transmission case shifter seal installer

fits  80-06 5-speed Big Twin (Excl. 2006 Dyna); 91-05 XL Sportster (NU)

Used to install & remove the main drive gear and installs the main bearing on 5-speed transmissions. Tool will provide a correct bearing angle for a straight insertion to prevent damage to the bearing bore during installation. Can be used without removing the transmission from the bike.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Transmission > MCS, 5-sp maindrive gear & bearing tool