fits  58-69 Big Twin (NU)

No. 13: For cam bushing in cam cover. Also fits 49-57 B.T with updated cam, bushings that are reamed out for 0.8125″ aftermarket replacement (which is standard aftermarket cam dimensions for 48-69). Dual end gauge pin, one side is a Go other side is No-Go gauge. Used to check if the tolerance of the bushing/bearing is within spec, or that a replacement is in order. For a quality job without guesswork.

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Engine Lower End > Fast Eddy, cam bushing Go & No-Go gauge pin

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Replacement for S&S ‘SuperStock’ ignitions.

Δείτε περισσότερα στον κατάλογο V-Twin

Home > Parts > Electrical > Ignition > Electronic Ignition > S&S, connector kit for SuperStock ignitions

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Replacement for S&S ‘SuperStock’ ignitions.

Δείτε περισσότερα στον κατάλογο V-Twin

Home > Parts > Electrical > Ignition > Electronic Ignition > S&S, VOES switch and hardware kit

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

3/16″ Inside Diameter. Used for connecting the VOES (Vacuum Operated Electric Switch) to the manifold. Replacement for S&S ‘Super Stock’ ignitions.

Δείτε περισσότερα στον κατάλογο V-Twin

Home > Parts > Intake > Fuel Injection & Carburetors > Carburetors > Other > S&S, hose 12″ for VOES switch

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Fits points type ignition wire with 3/16″ (4.8mm) diameter. This clamp that holds the ignition wire, that exits the bottom side of the nese cone (cam cover), away from the exhaust. Screws to bottom side of nose cone on 70-99 Big Twin models. Can be used in many other custom applications as well.

Δείτε περισσότερα στον κατάλογο V-Twin

Home > Ignition wire clamp, 3/16″. Chrome

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Fits electronic type ignition wire with 1/4″ (6.35mm) diameter. This clamp that holds the ignition wire, that exits the bottom side of the nese cone (cam cover), away from the exhaust. Screws to bottom side of nose cone on 70-99 Big Twin models. Can be used in many other custom applications as well.

Δείτε περισσότερα στον κατάλογο V-Twin

Home > Ignition wire clamp, 1/4″. Chrome

fits  00-17 Softail (NU)

Includes the 24983-00 oil screen and the 11301 o-ring. Used in the right side crankcase.

Δείτε περισσότερα στον κατάλογο V-Twin

Home > Parts > Engine > Lower End > Colony, oil screen kit

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Used to remove the camshaft gear; Note: Use 978294 tool to install/reposition the cam drive gear

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, cam gear remove tool

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Used to hold cam cover when removing / installing cam bushings

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, cam cover holding tool

fits  70-99 Big Twin (Excl. Twin Cam) (NU)

Used to line ream the cam cover bushing to the correct size, through the inner cam bearing; Case disassembly required; Note: See MCS 978293 for JIMS cam bushing & bearing alignment test tool

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, cam bushing line reamer tool