fits  55-06 Big Twin (Excl. 2006 Dyna) (NU)

Used to rotate the engine from the sprocket shaft (with 10 splines), when doing engine building, timing, pushrod or other adjustments and checks for which the engine must be rotated. The spline fit has intentionally been made with just a hair of extra play so the socket slides onto your sprocket shaft with ease, even if it’s an old shaft that has a couple burs or defects in it. Made from heat threaded 4140 steel. Cerakote finish.

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Engine Lower End > Fast Eddy, engine rotation socket. 10-spline

fits  06-17 Dyna; 07-17 Softail; 07-16 Touring (NU)

Used to rotate the crankshaft for timing or clearance checks. Fits the splines on the sprocket shaft. With a 1/2″ drive.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > General Tools > Hand Tools > Sockets > MCS, sprocket shaft rotating socket tool

fits  55-06 Big Twin (Excl. 2006 Dyna) (NU)

– Used to split the engine cases and easily break the sealer – Will split cases and also press the complete flywheel out of and into the right case on Timken bearing models – Some case pressing may require a hard cap. See 514024 for the optional hard cap to protect the sprocket shaft – This crankcase splitter is the only correct tool that will allow you to easily split the cases, without risk of damage, with a ratchet – Manufactured from 1/2″ thick A36 hot rolled steel – Installs to the primary side of the case. Note: See 514024 for the optional hard cap to protect the sprocket shaft. Note: For the 00-06 Softail engine this tool can be used for removing the flywheel from the left case only. Note: Do not use air or electric impact tools. Instructions included.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, crankcase splitter & flywheel removal tool

fits  55-06 Big Twin (Excl. 2006 Dyna) (NU)

Used to rotate the assembled engine, fits to sprocket shaft, when doing pushrods or engine timing; With 1/2″ drive; Note: Use with hand drivers only. Not to be used with power tools.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, sprocket shaft engine rotator

fits  06-17 Dyna; 07-17 Softail; 07-16 Touring (NU)

Used to hold flywheels in vice, with or without left case attached

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, flywheel holder tool

fits  55-06 Big Twin (Excl. 2006 Dyna) (NU)

– For sprocket shafts with 10 splines – Reversible ratcheting wrench – Used to rotate the crankshaft effortlessly, without damage to the sprocket shaft, when doing timing or clearance checks – USA made

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > Lang, sprocket shaft wrench

fits  55-06 Big Twin (Excl. 2006 Dyna) (NU)

– For sprocket shafts with 10 splines – Reversible ratcheting wrench – Used to rotate the crankshaft effortlessly, without damage to the sprocket shaft, when doing timing or clearance checks – USA made

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > Lang, sprocket shaft wrench