fits  00-17 Softail (NU)

Black Type III hard coat anodized finish. Stock ride height. 45mm billet aluminum twin tube design with 25mm piston reacts quickly for improved fluid flow. Deflective disc valving self-adjusts to frequency and ensures controlled performance. Low friction sealing system and sliding bearings for improved performance and feel. Three-step external knob adjustments allow fine-tuning of rebound. Stainless steel tie bar design and construction. In standard length for optimum ride quality and performance. Note: Standard duty is recommended for up to 250lbs. (113kg) total loaded weight. Heavy Duty application is recommended for over 250lbs. (113kg) rider/passenger total weight. Also, consider heavy-duty if the majority of your riding is two up with a passenger and/or gear.

Δείτε περισσότερα στον κατάλογο

Home > Parts > Suspension > Shock Absorbers Rear > Legend, Revo-A shock set. Black

fits  00-17 Softail (NU)

Used to install & remove the outboard balancer bearing on chain guide support plate. Also installs a new balancer bearing and counter balancer shaft.

Δείτε περισσότερα στον κατάλογο

Home > Workshop > VTwin Tools > Engine Lower End > MCS, balancer bearing tool kit

fits  00-17 Softail (NU)

Used to set-up correct alignment of the sprockets / balancer chain to insure maximum life and dependability from the balancer chain and bearings.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > General Tools > Specific Tools > MCS, balancer shaft alignment tool

fits  00-17 Softail (NU)

Used to install the inner engine balancer bearing (8992A / MCS 507698) in the left case. Work can be done on a workbench and does not require a press.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > General Tools > Specific Tools > MCS, inner balancer bearing install tool

fits  00-17 Softail (NU)

Used to secure the engine balancers when servicing the flywheel assembly. This tool locks into the balancer’s sprocket pin holes and prevents the balancer turning out of synchronization with the flywheel.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, balancer shaft retention plate

fits  00-17 Softail (NU)

A must for maintaining a long life of balancer drive chains and bearings. Takes the guess-work out of setting up the sprocket & chain assembly on Twin Cam Softail models. This tool must be treated with great care, as you would treat a micrometer.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, balancer shaft alignment tool

fits  00-17 Softail (NU)

Used to check the condition of the new or old interconnect seal H-D 45359-00 / MCS 981195. If seal leaks an over oil condition in the lower end can be created, resulting in increased oil carry over. Testing seal is advised each time the cam support is re-installed. Note: A leak-down tester, like JIMS 961581, is required

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, balancer interconnect seal leak test tool

fits  00-17 Softail (NU)

Used to accurately, and safely install the inner balancer bearing mounted in the left engine case. Tool is designed for both early and late Softail Twin Cam crankcases. Work can be done on a workbench without using a press.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, inner balancer bearing tool

fits  00-17 Softail (NU)

Aluminum with delring insert to help prevent marring; supports case underneath balancer bearing pads surface

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, TCB crankcase support block tool

fits  00-17 Softail (NU)

Used to hold the hydraulic tensioners in place while servicing the Softail engine balancing system.

Δείτε περισσότερα στον κατάλογο Workshop

Home > Workshop > VTwin Tools > Engine Lower End > JIMS, hydraulic balancer retaining tool